• Category:

    • silicone Comments Off
      Silicone_Coolant_Breather_Hoses_fits_MG_F_TF_Radiator_PRT_Upgrade_Stoney_Racing_01_eg Silicone Coolant Breather Hoses fits MG F TF Radiator PRT Upgrade Stoney Racing
      Silicone Coolant Breather Hoses fits MG F TF Radiator PRT Upgrade Stoney Racing

      Silicone Coolant Breather Hoses fits MG F TF Radiator PRT Upgrade Stoney Racing
      Stoney Racing MG TF 1.8 PRT Silicone Coolant Hose Kit. Note: Some types of coolant are not compatible with silicone hoses. This high quality reinforced silicone hose kit replaces 23 coolant hoses including the front radiator hoses, heater hoses and other minor coolant hoses at the front of the car and in the engine bay. The hoses are a direct fit for the Pressure Relief Thermostat (PRT) model which was fitted to late’03 onwards vehicles as standard. The hoses can also be used to retrofit a PRT to an earlier manual MG F or TF (from VIN YD522572 onwards) models. The majority of the hose will also fit earlier MG F models up to VIN YD522572 but one throttle body hose needs modifying by cutting the hose and rejoining it with a plastic or aluminium connector (not supplied) so that the end of the hose can be rotated 180 degrees, to fit the earlier model. Upgrading and relocating the original thermostat to a PRT is a common upgrade for earlier vehicles to help prevent head gasket failure. The PRT thermostat is not included but is commonly available, along with a few other parts listed below that you will need to fit a PRT to the vehicle. These parts are not supplied with this kit. Pressure Relief Thermostat Part no. Thermostat Blanking Plate Part no. Thermostat Seal Part no. Hose Connector Y-Piece Part no. Hose Connector T-Piece Part no. The above parts along with our hose kit covers everything you need to upgrade to a PRT. Note that there are two versions of hose #14 on the diagram in the gallery for this kit, a single piece for cars that came without a PRT and a 3-piece assembly for cars that came with a PRT. You will only need one of these hose assemblies for any particular vehicle. The hoses will also fit VVC models but the kit does not include the two additional VVC hoses for the oil cooler which are available as a separate kit. Available in our store in. Please note that all screens display colours differently and while we make every effort to ensure our photos are as accurate as possible on the majority of monitors and devices the product colour may vary slightly from the colour you see on screen. The kit is available with a full set of hose clamps using the options above. The three types of clamp we offer are shown below, but not all options will appear for some kits due to clamp size limitations. Spring clamps are the most commonly used type by vehicle manufacturers. They provide excellent evenly distributed clamping force and are generally the best option for clamping coolant hoses, but they can be fiddly to fit/remove, and being mild steel they are more prone to surface rust over time. Whilst this won’t affect the performance or lifespan of the clamp some customers prefer our stainless steel options below which tend to look better and still perform as they should. Worm-Drive clamps have slightly less evenly distributed clamping force as the Spring type clamps, but they are still a good quality clamp and usually easier to fit/remove in the tight confines of an engine bay. Being 100% stainless steel they do not rust, so we recommend this type of clamp if you are concerned about the appearance of your engine bay. T-Bolt clamps Not available for this product. For some vehicles the original clamps can be reused so we also offer our kits without clamps, but please be aware our silicone hoses are slightly thicker than the standard hoses so in some cases the original clamps may be too small. Fitment: Direct replacement for the standard hoses. Construction: 4.5mm 4-ply silicone with 3-ply polyester reinforcing. Max Operating Pressure: >7bar. Operating Temperature range: -50°c to 180°c. Occasionally a hose may need to be trimmed slightly which can be done with a sharp utility/stanley knife with a NEW blade using a hose clamp as a guide to get a straight cut. More Stoney Racing Products. Looking for a silicone hose kit for your vehicle? How about exchanging your old rubber hoses for a FREE Silicone Hose Kit? If we don’t already produce a kit for your car and you can supply us with the standard hoses we may be able to have a silicone hose kit made up for you FREE of charge! This is subject to your car being one we are interested in making a kit for, we may not be able to make a kit for your vehicle if it is rare or not popular for modifying or use in motorsport. The turnaround for this is around 5-7 weeks from when we receive your stock hoses, so unless you can source a spare set to send us your car would need to be off the road for this period. We are a British-based business located in Shropshire, all our stock is dispatched from our UK premises. We do not dispatch orders on weekends or UK bank holidays. Unfortunately our workshop is on a site that is strictly no retail customers allowed so we are not able to offer collection on our items. Important for EU buyers: Following new EU VAT rules goods imported from the UK to EU countries now require VAT to be paid to your country, but UK VAT is no longer payable. These terms do not affect your statutory rights. This item is in the category “Home, Furniture & DIY\Plumbing & Fixtures\Other Home Plumbing & Fixtures”. The seller is “stoney-racing” and is located in this country: GB. This item can be shipped worldwide.
      • Colour: Red
      • Clamp Kit: SS Worm-Drive
      • Sub-Type: Silicone
      • Modified Item: No
      • MPN: MGTF-0002
      • Item: Hose Kit
      • Custom Bundle: No
      • Unit Type: Unit
      • Unit Quantity: 26
      • Brand: Stoney Racing
      • Non-Domestic Product: No
      • Featured Refinements: Silicone Hose
      • Type: Hose Kit

      Silicone Coolant Breather Hoses fits MG F TF Radiator PRT Upgrade Stoney Racing

      Tags: , , , , , , , ,